Bambu Lab 3D printer troubleshooting
25 guides to fix Bambu Lab 3D printers: the symptom, the likely causes, how to check which one is yours and the step-by-step fix, with official sources from Bambu Lab.
Printers covered: A1, X1, X1 Carbon, X1E, P1P, P1S, A1 mini, H2D, H2D Pro, H2S, P2S, X2D and 2 more.
Each guide summarises the official documentation and says whether usi3d has already verified it on a machine.
Adhesion and first layer (3 guides)
- A1 and A1 mini: first layer too low, wavy or scraping the plate (hotend shifting)
On the A1 or A1 mini the first layer comes out too squashed, wavy, with raised edges or peeling off, or the nozzle almost rubs the plate and hardly any plastic comes out.
- Bambu Lab build plates: print won't stick, plate not recognised or not matching the G-code
The first layer does not grip the Bambu Lab plate, or the printer complains about the plate: the marker is not detected (0300-8006, 0C00-0300-0002-000C), the detected…
- X1: Micro Lidar alerts (dirty lens, failed calibration, nozzle height) and first layer inspection
The X1, X1 Carbon or X1E shows Micro Lidar alerts such as «Micro Lidar lens seems to be dirty» (0C00-0100-0001-0004), «Failed to calibrate Micro Lidar»…
Extrusion (11 guides)
- A1 and A1 mini with AMS lite: won't load, won't extrude or won't pull the filament out of the toolhead
With the AMS lite, the A1 or A1 mini stops when loading or changing colour with alerts such as «Unable to feed filament into the extruder», «Failed to extrude the…
- A1 and A1 mini: not extruding or under-extruding (clogged nozzle, slipping extruder or nozzle too low)
The A1 or A1 mini extrudes no filament or too little: the first layer comes out with almost no plastic, the extruder gear clicks and skips, or it turns but nothing comes…
- AMS 2 Pro or AMS HT: the printer doesn't detect it or it won't dry the filament
The printer does not recognise the AMS 2 Pro or the AMS HT: on the AMS 2 Pro, the LEDs of all four slots double-flash red and it does not appear on the screen or in the…
- Flow dynamics (K factor) and flow rate calibration in Bambu Studio: when to run it and why it fails
Corners come out rounded or bulging, lines are missing or overlapping, the top surface is rough or blobby, or automatic flow dynamics calibration returns an odd value or…
- H2D: extrusion motor overloaded (0300-0900-0002-0001) or one nozzle stops extruding
The H2D pauses the print with an alert saying the extrusion motor is overloaded and that the extruder may be clogged or the filament stuck in the toolhead, or one of the…
- H2D: the two nozzles don't line up (shift when switching nozzles) or nozzle offset calibration fails
In a print using both nozzles, what one nozzle prints is offset from what the other prints, like a step or a layer shift right at the nozzle change, or the nozzle offset…
- The AMS won't load filament: «Failed to feed», assist motor overloaded or no extrusion
With an AMS (also AMS 2 Pro or AMS HT) loading or a colour change stops with an alert: the filament does not leave the AMS (0700-8005, «Failed to feed the filament…
- The AMS won't unload filament: it won't leave the extruder, won't return to the AMS or «filament broken in the toolhead»
When unloading or changing colour, the AMS stops with an alert: it cannot pull the filament out of the extruder (0700-8003), cannot return it to the AMS (0700-8004…
- The filament cutter gets stuck («The cutter is stuck») or fails to cut
When unloading or changing colour, the printer stops with «The cutter is stuck» (for example 0300-800B, 0700-8002 with the AMS or 1200-8002 with the AMS lite) or with…
- X1 and P1: clogged nozzle or hotend (0300-4006) and how to clear it
The X1 or P1 stops extruding or extrudes little and unevenly, the filament curls when extruded by hand, or the printer reports a clogged nozzle (0300-4006 or 0300-8016).
- X1 and P1: the extruder clicks, chews the filament or is clogged (cleaning and greasing)
The X1 or P1 extruder clicks or grinds, there is dust or filament debris on the yellow gear, the filament comes out chewed or deformed next to the gear, or filament will…
Mechanics (2 guides)
- Noise or friction on the axes: cleaning and lubricating rods, lead screws and pulleys (X1, P1 and A1)
The printer squeaks or makes noise when the toolhead or bed moves, the Z axis moves jerkily, marks or vibration appear on the walls after a lot of ABS or ASA printing…
- Tensioning the belts on the X1, P1, A1 and H2D (oval circles, ringing or tension alert)
Circles come out oval, ringing or dimensional errors appear, the printer warns after calibration that a belt needs tensioning (the A1 asks through an HMS alert) or it…
Electronics (4 guides)
- A1 and A1 mini: Z homing or bed levelling fails (hotend eddy current sensor)
The A1 or A1 mini reports «Z homing failed» or levelling fails: the toolhead comes down a little and stops without touching the bed, drops quickly and goes back up, taps…
- Fan error: hotend fan running slow (0300-0300-…) or part cooling fan stopped (0300-0400-0002-0001)
The printer warns that the hotend (heatsink) fan is slow or stopped, for example 0300-0300-0002-0002, or that the part cooling fan is slow or not spinning…
- Nozzle or bed temperature errors (HMS 0300-0200-… and 0300-0100-…)
The printer shows a nozzle temperature error (for example 0300-0200-0001-0001, heater short circuit, or 0300-0200-0001-0007, sensor open circuit; the A1 usually shows…
- X1 and P1: homing or bed levelling fails (Z homing failed, plate not placed properly, force sensors)
While preparing a print, the X1 or P1 stops with «Z-axis homing failed» or with alerts such as 0300-0D00-0002-0001 (bulge on the plate or dirty nozzle)…
Connectivity and firmware (4 guides)
- My Bambu printer won't join Wi-Fi, won't bind to Bambu Handy or Bambu Studio, or cloud access fails
The printer will not join the network, gets no IP address (it shows 0.0.0.0), says the password is wrong, does not appear when binding it in Bambu Handy or Bambu Studio…
- My Bambu printer won't read the microSD card or shows card errors
The printer asks for a microSD card (0500-400C) or reports that the card is write-protected (0500-4016), has damaged sectors (0500-402F), has a read/write error…
- The Bambu camera won't show in Bambu Studio or Bambu Handy (black screen or Liveview error)
The live video (Liveview) does not load: black screen, an error while initializing, loading or connecting, or the alert «Liveview service is malfunctioning»…
- The Bambu firmware update fails or can't be done online (updating from the microSD card)
The update download stops or fails, the printer has no internet access to update, you need to go back to an older version, or after connecting an AMS Hub the printer…
Error codes and messages (1 guide)
- Bambu Lab: what an HMS code or an error code means and how to find its guide
The Bambu Lab printer (or Bambu Studio or Bambu Handy) shows an alert with a code: a long one made of four blocks such as 0300-0200-0001-0007 (HMS code), or a short one…
Products that may help
Products from the usi3d shop that fit these guides, chosen for the fit and not for the commission. Check that they work with your printer before buying.
Symptoms in the Bambu Lab guides
- The printer shows an error code or message
- Clogged nozzle or hotend
- The multi-material system fails (does not load, cut or jams)
- No filament comes out
- Does not stick to the bed
- Uneven first layer (thin and thick areas)
- Too little filament (under-extrusion)
- Ripples or echoes on the walls (ghosting)
- Shifted layers (layer shift)
- Unlevel or warped bed
- Homing or a sensor fails (endstop, levelling)
- Does not connect to Wi-Fi or the app
- The print will not come off the bed
- The extruder clicks or skips
- The extruder grinds or snaps the filament
- Too much filament (over-extrusion)
- Blobs and zits on the surface
- Noise or rubbing when the axes move
- Periodic bands or steps in Z
- Loose belts
- Temperature error (MINTEMP, MAXTEMP, thermal runaway)
- The hotend or the bed does not heat
- A fan does not spin or is noisy
- Does not read the SD card or USB drive
- Problems after a firmware update
Other brands
Can't find your case?
Tell usi3d's AI about your case: choose your printer, describe what you see and add photos if you like. It proposes checks step by step, with their sources.