The hotend or the bed does not heat
9 usi3d guides for “The hotend or the bed does not heat”, each with the likely causes, how to check which one is yours and the step-by-step fix, with each manufacturer's official sources.
One applies to any FDM printer and 8 are for Anycubic, Bambu Lab, Creality, Elegoo and Flashforge printers.
Each guide summarises the official documentation and says whether usi3d has already verified it on a machine.
Any FDM printer (1 guide)
- The hotend or bed won't heat up, or takes too long
You set a temperature and the hotend or bed doesn't rise, rises very slowly or stays far from the target; often the printer ends up showing a preheat or heating error.
Anycubic (1 guide)
- Kobra S1 or Kobra 3: errors 10121, 10122, 10123 or 10124 (bed or printhead not heating, or thermistor fault)
The Kobra S1 or Kobra 3 stops with 10121 (hotbed heating abnormal), 10122 (extruder heating abnormal), 10123 (hotbed NTC abnormal) or 10124 (extruder NTC abnormal).
Bambu Lab (1 guide)
- Nozzle or bed temperature errors (HMS 0300-0200-… and 0300-0100-…)
The printer shows a nozzle temperature error (for example 0300-0200-0001-0001, heater short circuit, or 0300-0200-0001-0007, sensor open circuit; the A1 usually shows…
Creality (3 guides)
- Ender 3 V3 or V3 Plus: the hotend does not heat (error 2564 or 111) or it restarts while heating
The Ender 3 V3 or V3 Plus shows «Error, key: 2564, the extruder is not heating as expected», gives error 111 at start-up or while printing (communication between the…
- Ender 3 V3 SE: nozzle or bed temperature too low or too high, or it restarts while heating
The Ender 3 V3 SE reports that the nozzle or bed temperature is too low (it does not reach the set temperature in time) or too high (usually right after switching on)…
- The K1 shows a «key» error for the print head or bed (2000, 2001, 3002, 2564, 2565)
The K1, K1C or K1 Max screen shows an «Error, key: …» window and the printer stops or does not finish booting.
Elegoo (2 guides)
- Centauri Carbon 2: errors 101, 102, 103 or 104 (bed or print head not heating, or a thermistor fault)
The Centauri Carbon 2 stops with error 101 (check the heated bed and its wiring), 102 (heated bed temperature sensor disconnected), 103 (check the print head and its…
- Centauri Carbon: errors 101, 102, 103 or 104 (bed or printhead not heating, or a thermistor fault)
The Centauri Carbon stops with «Error Code: 101» (the heated bed did not heat up as expected), 102 (anomaly reading the bed NTC thermistor), 103 (the print head did not…
Flashforge (1 guide)
- Adventurer 5M: temperatures at 0 °C or negative, or errors E0002, E0005 or E0011
The Adventurer 5M (or 5M Pro) shows the nozzle and bed at 0 °C, or the nozzle at a negative value and not heating, or it stops with «E0002 Communication with MCU…
Products that may help
Products from the usi3d shop that fit these guides, chosen for the fit and not for the commission. Check that they work with your printer before buying.
More “Electronics” problems
Guides by brand
Can't find your case?
Tell usi3d's AI about your case: choose your printer, describe what you see and add photos if you like. It proposes checks step by step, with their sources.